How to unclog a bathtub with standing water

Have you ever tried to unclog a bathtub with standing water? Although this may seem like an easy task when looking at the tub from above (see image 3), there is more than one way that could work for your situation.

How to unblock a bathtub

If you have a blocked bathtub, you can do a few things to unblock it. First, you can try plunging the drain to dislodge the blockage. Using a drain snake may help you see if you can clear the blockage that way.

If neither of those options works, you can always call a plumber to come and take a look.

How to unclog a bathtub with standing water: 10 tips.

If your bathtub is full of standing water, you can do a few things to unclog it. First, try using a plunger to see if that will dislodge the clog. If that doesn't help, you can use a drain snake or a drain auger. If you still can't get the clog to budge, you may need to call a professional plumber.

Meanwhile, here are ten tips for unclogging your bathtub:

1. Try using a plunger.

2. If that doesn't work, try using a drain snake or a drain auger.

3. If you still can't get the clog to budge, you may need to call a professional plumber.

4. In the meantime, here are ten tips to help you unclog your bathtub:

5. Try using boiling water.

6. Try using a mixture of baking soda and vinegar.

7. Try using a wire hanger.

8. Try using a plumber's snake.

9. Try using a power washer.

10. Try calling a professional plumber.

Learn what’s causing the blockage.

The first step in unblocking a bathtub is to figure out what's causing the blockage. There are a few things that could be causing your tub to overflow and clog:

Hair and soap scum in your drain can be tough to remove, so check this area first. If you find hair tangled around one or more drain holes, try using a pair of pliers to pull it out.

Consider using a cleaning product like Drano or CLR; these will dissolve buildup in your pipes and should help clear up any blockages that have also occurred there.

Check over the overflow drain hole in your tub's faucet—often times this can become clogged with objects such as toys or other debris that has fallen into it over time.

To fix this problem, unscrew the little cover on top of this hole (it should just pop off).

Then use either an old toothbrush or other small tools (like chopsticks) under running water until all visible particles have been removed from inside this part of your faucet assembly (make sure not to push anything down into other factors where it might cause further problems). 

If nothing comes out after doing this several times, try taking apart your entire faucet assembly so you can get at everything inside quickly without having to take apart individual pieces one by one, which could take forever.

Clear any standing water from the tub.

Clear any standing water from the tub before you start to use it. This will help you avoid slips and falls, and it will also keep the tub clean. Standing water can be a breeding ground for bacteria, so getting rid of it is essential before you start using the tub.

Create a seal for your drain auger.

To create a seal around the drain, you'll want to use one of the following:


Wet/dry vacuum

A wet/dry vacuum with a hose attachment

A snake (a long flexible hose that fits into the pipe)

Power auger (also called an electric drain cleaner)

Chemical drain cleaner

Add more water to the drain if needed.

If the water in the drain isn't draining correctly, you may need to add more water. Pour a cup or two of water down the drain, and then wait a few minutes to see if the water drains properly.

If it doesn't, you may need to add more water, or you may have a clog in your drain.

How to unclog a bathtub with no overflow

If you have a bathtub with no overflow, the first thing you'll need to do is remove the drain cover. Once the surface is off, you'll be able to see the clog. If the clog is close to the drain, you can try to remove it with a plunger.

Next, you'll need to use a plumbing snake to clog further down the drain. To use the snake, insert the end into the drain and turn the handle to push the snake through the clog. Once the snake is through the clog, turn the handle the other way to pull the clog out of the drain.

How to unclog a bathtub with a slow drain

If your bathtub drain is draining slowly, there are a few things you can do to try and unclog it:

You can try pouring a pot of boiling water down the drain. This will help to loosen any buildup that may be causing the clog.

You can use a plunger to dislodge the clog if that doesn't work.

Cover the overflow drain with a rag to create a seal so the plunger can work effectively.

You may have to use a plumber's snake to reach the clog and break it up.

How to unclog a bathtub with no stopper

If your bathtub is clogged and you don't have a stopper, there are still a few things you can do to try and unclog it. First, try using a plunger. Next, try a wire hanger; you can fish the clog out; if neither of those works, you may need to call a professional.

How to unclog a bathtub with a stopper

If your bathtub has a clog and you can't seem to fix it, there are a few things you can try. One way to unclog a bathtub with a stopper is to use a plunger. To use the plunger, it should be placed over the drain and pushed and pulled. The plunger up and down.

This should help to loosen the clog. Plungers that don't work can be replaced with a plumbers snake. Put the snake counterclockwise into the drain. Thus, you will be able to break up the clog.

Lower the auger if you’re using a powered auger.

Now that you've removed the hair drain the water in your tub and checks to see any other obstructions. If there are, repeat these steps until you can drain all of the standing water from your bathtub.

If you have a powered auger or plunger: Lower the auger or plunger by rotating it to create space for more water to flow down through the drain.

This may not be possible with some models of either tool; consult your product manual for instructions specific to yours.

If using a snake: Twist it around until it can reach as far down into the pipes as possible without getting stuck or hitting anything else inside of them (this can damage both your snake and whatever is inside).

Pull out the machine and remove debris from the claws or cable.

Once you've removed the drain plug and water has drained out of your tub, use a rag to wipe off any debris that may have built up in your machine's claws or cable. If you're using a plunger, remove it before pulling out the device.

Remove your auger or plunger after you’ve finished using it.

To remove the auger or plunger, slowly reverse the steps you followed to insert it. Ideally, this will be as easy as pushing it back out of the drain hole.

If you're having trouble removing it, try gently pulling on it from above with one hand while pushing on it from below with your other hand.

To clean your auger or plunger, use soap and water to wash off any debris that might have gotten stuck inside during your previous attempts at unclogging.

Then, let the device air dry before storing it in a safe place where it won't damage by moisture or other household objects (like little brothers).

Do not store your auger or plunger in standing water. This can cause permanent damage to its structure and make future uses much more complicated than they need to be—and we all know how annoying clogged drains are.

If you haven’t cleared the clog, try another method.

If you haven't cleared the clog, try another method. Alternatively, if you don't have a plunger at home, you may be able to borrow one for free from your local hardware store or houseware shop.

Finally, if you have a drain auger and have already tried it in your bathtub and failed, try again with more force or a different-sized tool.

If all else fails, call in a professional plumber who can clear the blockage with specialized equipment that might work better than what's available at home—or give them an excuse to use their impressive collection of small tools.

Unclogging your bathtub can be easier, especially when you have instructions.

You're ready to start, but what is the first thing to do? First, you need instructions. You may think that unclogging your bathtub with standing water is as simple as throwing in some draino, but there are a few steps to ensure that your procedure will be effective and safe.

Turn off the faucet at the wall before proceeding with any other actions, so no more water flows into or out of your tub. Next, remove all visible objects inside the bathtub; these could cause damage if they fall during cleanup.

Finally, ensure no obstructions, such as hair clogs or soap residue stuck around drains (which can make it harder for water to flow through).

 Watch How to unclog a bathtub with standing water

How to unclog a bathtub with standing water (FAQs)

What you need for Unclogging a Bathtub

To unclog a bathtub, you need a few supplies. You will need a plunger, a plumber's snake, and vinegar. You will also need a bucket, some rags, and some gloves.

First, put on the gloves. Then, using the plunger, try to unclog the drain. If that does not work, use the snake. If the snake does not work, mix equal parts vinegar and water and pour it down the drain.

You should let it sit for a few minutes, then flush the drain with hot water. If none of these methods work, call a plumber.

Finding the source of the clog

First, identify the source of the clog. This can be tricky, as clogs can form in different sink parts. If the clog is in the drain, you may be able to clear it with a plunger.

If the clog is in the trap, you may need to disassemble it and remove it with a wire or other tool. Sometimes, the clog may be in the pipes leading to the sink, so you'll need to call a plumber.

What can you do to prevent clogs?

There are several things you can do to prevent clogs in your drains.

First, be sure to only put things down the drain meant to go there. That means no grease, oil, or food scraps.

Second, run hot water down the drain regularly to keep things moving. Third, invest in a drain strainer or hair catcher to keep hair and other small items from going down the drain.

Lastly, don't reach for the drain cleaner immediately if you have a clog. Instead, try a plunger or a snake first to see if you can dislodge the clog.

How to unclog a bathtub with standing water

If you have a bathtub full of standing water, there are a few things you can do to try and unclog it.

First, you can try using a plunger. Put the plunger over the drain and see if you can push the clog through. Alternatively, you can use a drain snake. Use the drain snake to see if you can perform the clog loss.

If neither of those methods works, you may need to call a plumber.

How to unclog a bathtub with a plunger

If you have a clogged bathtub, there are several ways to unclog it. One way is to use a plunger.

First, make sure the plunger is the right size for the bathtub. You will also need to add some water to the tub so the plunger can create a seal.

Once you have done this, you will need to push and pull the plunger up and down. You may need to do this a few times before clearing the clog.


The water in your tub can be a breeding ground for bacteria and mold, so you should keep it clean. You can unclog a bathtub with standing water by following the instructions mentioned above.